8 English reviews written for BondTech CHT Coated Nozzle M6 x 1.75 mm
27 customer reviews in all languages
| 5 stars | | 57 | (83%) |
|---|---|---|---|
| 4 stars | | 5 | (7%) |
| 3 stars | | 3 | (4%) |
| 2 stars | | 2 | (2%) |
| 1 Stars | | 1 | (1%) |
Filter reviews:
-
Janovich
October 04 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. -
KP
September 02 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. too expsive for what you get
Rated with 2 out of 5 stars.
I installed this nozzle on a Ender 5+, with a bondtech Phase 4 (copperhead) DDX V3 direct drive extruder for 1.75mm filament.
The print quality is good, but the nozzle clogs more easy then normal nozzles, especially on filament changes.
They are also difficult to unclog.
IMHO this works better if you use 3mm filament.Was this rating helpful? (3) (0)
-
Thomas
July 04 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Great upgrade
Rated with 5 out of 5 stars.
After 18 months of light use I replaced my stock Prusa nozzle with a 0.4mm CHT. Performance of the old nozzle had seriously degraded till I could only print PETG at 30% speed and got increasingly rough results even in PLA. New nozzle - 150% speed PETG on first go with pristine results! And it can probably go faster still. Very pleased with the upgrade. In fairness I may have got a big improvement with just a new basic brass nozzle, but probably not to this level.
Was this rating helpful? (4) (0)
-
Marc
January 28 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. I purchased a 0.6 and 1.4mm
Rated with 5 out of 5 stars.
At first I wanted to try the 0.6mm nozzle. However, 3djake only had the 1.4 in stock. I knew that my ender 3 v2 with a e3d v6 hot end would be far to small for this nozzle. I was correct. I printed a vase that originally took me on a brass 0.4, 14 hours. It took me 1 hour. Other than spiral/vase mode. I this nozzle is absolutely useless at slow speeds and small prints.
I eventually got a hold of a 0.6mm nozzle. I can print a lot faster without the dreaded clicking from the original extruder. I've since upgraded to a BMG extruder. I can print my test xyz cubes in 15 minutes however, i cannot get my printer dialed in to keep up with the flow and movement speeds. So until I can dial my printer in, i cannot take advantage of the extra flow these nozzle give me.
If you are looking at upgrading to a volcano but are not an expert at setting up a printer. Buy one of these nozzles. You will save money and get the same benefits of a volcano hot end.Was this rating helpful? (2) (0)
-
Louis castle
December 27 2021
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. nozzle
Rated with 3 out of 5 stars.
seems very good, sadly mine arrived broken
Was this rating helpful? (0) (10)
-
Lapjoint
November 12 2021
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Works like a charm
Rated with 5 out of 5 stars.
I used to print bigger parts with a .8 mm nozzle on an E3D Volcano hotend, which I had to swap out for my regular E3D V6. With these nozzles, I can print at the same flow rates and with .8 mm or 1 mm nozzles with just a simple nozzle change, which makes it much, much easier to go back and forth between nozzle sizes. I also got the impression that these ooze a little less than the longer Volcano nozzles.
Beautifully made and well worth the higher price.Was this rating helpful? (9) (0)
-
Christian Woznik
November 10 2021
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Unglaublich
Rated with 5 out of 5 stars.
Ich muss sagen, ich war skeptisch. Wie kann eine so geringe Änderung einen solch positiven Effekt haben?
Ich erreiche mit der Düse in 0,6mm nun um die 20mm^3/s in einem ANet ET4 Pro. Und das Problem ist nun der Extruder, der einfach nicht mehr mitkommt.
Deswegen habe ich mir nun auch einen BondTech Extruder zusammen mit einem Slice Engineering Coperhead Heater Block gekauft. Ich bin gespannt, was dann möglich sein wird.
Ein Nachteil gibt es bei dem ET4 Pro. Die Düse hat ein längeres Gewinde als die beiliegenden. Dadurch sitzt entweder der Heatbreak oder die Düse nicht vollständig mehr in dem Heizblock. Bei dem ANet ET4 Pro würde ich definitiv direkt auch eben diesen tauschen um sich unnötige Mühen zu ersparen.Was this rating helpful? (1) (1)
-
Jarl Gullberg
November 05 2021
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Incredible performance
Rated with 5 out of 5 stars.
This nozzle is no joke, and can cut print times by two thirds on an average Prusa i3 MK3S. I went from 15mm³/s to 50 mm³/s, and ate an entire 1KG roll of PLA in less than three days. I'm shocked and impressed by how much of a difference this nozze made.
Was this rating helpful? (9) (1)
Magazine Articles:
Discover 3DJake:
-
Delivery in 3 business days.
More than 10.550 products
We deliver worldwide to
more than 40 countriesSecure payments
with SSL encryption technology
Favorite Nozzle
Rated with 5 out of 5 stars.
CNC kitchen channel benchmarked this nozzle and it always came out on top compared to anything else in printing speed, and with a fairly large margin. Its a must have for printing big items fast.
However they are difficult if not nearly impossible to unclog in my experience. Fairly expensive too.
Was this rating helpful? (4) (1)