6 English reviews written for Extrudr Green-TEC PRO Black
34 customer reviews in all languages
| 5 stars | | 35 | (62%) |
|---|---|---|---|
| 4 stars | | 13 | (23%) |
| 3 stars | | 3 | (5%) |
| 2 stars | | 1 | (1%) |
| 1 Stars | | 4 | (7%) |
Filter reviews:
-
-
TerTerro
October 27 2021
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Review
Rated with 1 out of 5 stars.
Temp resistance is false. Tested a piece 4mm thick solid infill and at 60c it starts to bend. At 100c easy deformed.
Also layer adhesion not great.Was this rating helpful? (2) (4)
-
Sam
September 24 2020
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Top quality
Rated with 5 out of 5 stars.
Prints beautifully, just like pla, nozzle 200° and 55° bed (ultrabase) with no fan.
No unpleasant smell like with abs, no need for enclosure, incredible strong layer adhesion, great strenght with 1.8mm walls and temperature resistance (tested at 150° in oven for more than 1h and it just got little soft but it didn't melt or shrink or deform or change the shape).
Compared to abs it's far superior in every way, and even it's almost twice the price of abs i might say it's worth it since it's better in every single way and it uses much less energy to print.Was this rating helpful? (4) (2)
-
Vaggelis
July 01 2020
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Bit expensive but very nice
Rated with 5 out of 5 stars.
Good mechanical properties, matte finish and melts great, albeit a bit pricey.
Was this rating helpful? (0) (0)
-
Bas Borgignons
May 18 2020
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Very, very good printresults, but check filament dimensions!
Rated with 4 out of 5 stars.
The results are absolutely stunning, and very strong. Just be sure to check the filament dimensions, the roll I had was what I would call out of tolerance. The filament was quite oval, and undersized (1.73mm by 1.70mm, measured with a good micrometer). I got only one roll, so this might be from a bad batch. However, after compensating for this in the slicer the results I got were good enough to make this one of my favourite filaments.
Was this rating helpful? (2) (1)
-
Nicholas
March 14 2019
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Review written by Nicholas
Rated with 5 out of 5 stars.
nice matte finish if run at 200° and no adhesive required on glass at 50-60°, bit of 3m tape for a nice lower surface finish. resists heat just fine and prints just as easy as PLA.
Was this rating helpful? (1) (1)
Magazine Articles:
Discover 3DJake:
-
Delivery in 3 business days.
More than 10.550 products
We deliver worldwide to
more than 40 countriesSecure payments
with SSL encryption technology
Not temperature resistant
Rated with 1 out of 5 stars.
Temperature resistance is not very good, when dipped in some water at 95C it becomes very soft and thin walls are floppy. I contacted Exrudr for advice but received no reply.
Was this rating helpful? (7) (1)